Thursday, January 19, 2012

Let's Make Cosplay: Transformation Wand



Ever wanted to make a transformation wand? A friend requested this prop and bam, here it is! You can find the video for it here! http://www.youtube.com/watch?v=MOgQGGOCoCg

The materials I used were wood rod balls and hearts, friendly plastic, four 1" Philips head wood screws, 1mm. and 3 mm. PCV sheeting, gray paint, sliver paint, purple paint, nail decorations (rhinestones), and gloss varnish.

The tools I used were a saw, a heat gun, a file, a hot knife, a box cutter, a marker, a circle template, some super glue, some paint brushes, and sponge brushes.

I’ve never made a prop like this before so I tried my best. Instead of crafting a lot of the parts by hand I opted to use a lot of wood bits that were already carved. I purchased some wooden balls and a wooden heart piece for the prop.

Since the balls came with holes already drilled into a section of it, I figured I would use those holes to mount them into the handle. I expanded the holes at the bottom of the balls and then mounted a screw into holes. What I basically did was put a screw into the bottom of the hole before I filled the hole with friendly plastic to hold the screws in place so they wouldn’t move. After that, I drilled holes into the dowel rod and twisted the knobs into the dowel rods to get them on and secure.

At the base of the handle, I used the rasp and file to carve a groove into the dowel rod right above where the ball attaches. I cut and sanded it out as best I could. After that small step, I got a whole mess of friendly plastic and the two wooden hearts I purchased. I started by sticking one heart in place with the friendly plastic and tried to center it as best as I could before I did the same with the other side with the wood heart. I tried to make it parallel as best as I could and left a tiny bit above the sphere to do details.

As a note, it stinks to use filler to do shaping work because it is hard to see. When you paint it filler shows all the problems that you made so you need to make sure you do a perfect job when shaping filler.
After that, I progressed to the ring around Saturn. I used a circle template and figured out how big the size of the ball was and how big I wanted the ring to be. The ring’s total diameter was 3 inches. I took the circle template and drew a circle for the sphere.

On the template it shows how to do a cross and extend it past the circle. You can draw your inner circle and then you can draw an outer circle that lines up correctly with the inner circle and keeps it centered. I cut the circle out of 1 millimeter PVC Sheeting. You can cut this material with scissors. I opted to cut the material with scissors for the outside but I used the hot knife for the inside to make it smoother so it would fit well around the ball it was going around. It is best to use hot knife to cut curves or execute precision work.
When he cut out the circle I cut the inside a little smaller than what I drew it as so that it would be slightly smaller than the ball. This was to ensure a snug fit against the ball. After this was done, I cut a six sided star out of 3 millimeter PVC sheeting. It is hard to shape small pieces of PVC because if you are not careful it can look bad and not uniform. You need to control your cuts because of how the material goes. To counter this, I took the rasp to even it out as best as I could.

The ring was snugly put in place and superglued down to the ball before I stuck the star into place. In After that, I put a glob of friendly plastic into the small hole I drilled and pushed the star in. After that, I made some small putty like balls and stuck them right onto the prop before I painted it purple.

Since I was rushing, I tried to use fabric paint. That was the worst mistake because it gets really blotchy. I ended up sanding it all off and redoing it in acrylic. I based the silver bits with grey paint before I painted the metallic paint on. After that was done, I bought some nail jewels for the rhinestone gems and stuck those onto the heart. The last thing that needed to be done was the small detail on the small star, which I marked with a marker before I varnished the entire thing with a gloss varnish.

That explains this prop! As always, if you have any questions, please feel free to email us at finalcosplaycorps@yahoo.com! 

Saturday, January 14, 2012

Let's Make Cosplay: Golem Cosplay

This was an interesting costume that I chose to start on four days before Youmacon. It’s from one of my favorite games, the Legend of Mana. Thankfully I already had schematics ready for this costume, The only reason that I was able to finish this cosplay in time for the con was because I had plans already in place and I knew what I wanted to do and how I wanted to execute the cosplay. If you are interested in looking at the videos corresponding to the creation of this prop, please go to the following link.

http://www.youtube.com/user/FinalCosplayCorps#p/search/0/mBQB4gftg3U This link is to the first video. The other ones following it will be in the section to the right of the video.



To lay the groundwork for this costume, I started with circles of foam stacked on top of each other. Think of how onion rings are stacked up when they’re brought out to you at a restaurant and you’ll get the idea. The trick with foam is to use it as effectively as you can with circles and compound tape. When you remove cavities from the foam, keep them and use that foam for other exposed sections. If you were to make a circle, you could cut a run and then stack another ring on top of the ring before it to make layers stack together.
You’ll want to start with two circles. One will need to be smaller than the other so that you can stagger then properly. Think about how you give a baby a bunch of different sized circles and then teach them to stack them into a cone shape. When you cut your circles, make sure you are CAREFUL about the THICKNESS of the circle. If you cut your circles too thin from the foam it will make one side either weaker or make it weird when gluing. If you cut it too thick it will be too hard for you to move in the actual costume. I usually say that you need a 2 inch minimum for EPS foam. If you opt to use another kind of foam you will need to mess around with what thickness will be the most ideal.

There’s a variety of ways I chose to draw my circles. If the circles are going to be relatively small, I’ll use plates. Since I needed really large circles for this prop since it was going to be going around my body, I constructed a compass. Basically, you’ll need to create an axis and then create a method to be able to pivot around that axis. I took a ruler and measured out what I wanted the diameter and the radius of the circle to be.  After I determined where I wanted the center of the circle to be and how big the radius and diameter was and marked those, I took the compass and stuck the pointy end in the foam where the center of the circle would be and took a marker and spun it around to hit all the points I made measuring out the radius from the center of the circle. If you cut out a center piece you can take that piece and use that hole for the center of the next layer so it makes the same circle every time. This is extremely important when you’re doing multiple circles. If your circles are off center you can have lots of missed spots and it becomes problematic.
Before you glue these layers together with these hard edges you will want to cut the basic shape of the prop. Instead of cutting out the big edges after you glue everything together you will have the basic shape. I like to stack the layers all together, draw where I will need to cut, then cut out the foam so it will be in the shape I need it for after it’s glued together. It’s easier to cut a two inch wedge than huge chunks of foam glued together. However, doing this can lead to some issues, so make sure you don’t cut too deeply in case something goes wrong during gluing. 

As a side note, it is not good to combine different kinds of foam. Spray foam will eat EPS foam. DO NOT try to patch holes in EPS foam with spray foam. I choose to use EPS foam because it’s way cheaper by volume. Spray foam is usually full of cavities and useless. It’s good for putting things together fast but you often lose time by filling all the holes that spray foam has. Finishing spray foam also takes  lot longer because of how coarse it is. Whatever you do, if you choose one kind of foam stick with it.

Once you had your basic shape cut out and glued together you can get a decent sanding tool and go in to start shaping. Since foam is really soft you don’t need a super hard tool. When you’re sanding you need to be careful of the layer lines. Unless you’re using  a huge block of foam you will getting stuck with sanding many layers. You’ll need to mask them as well as you can otherwise you’ll be able to see the rings when you paint. The spray adhesive is denser than the foam itself so lines can be evident even if you sand everything smoothly. You need to get the rings out later, so you don’t have to get it perfect for now. You can sand it again after you use the plaster of paris.



After that, you’ll need to start working with the PVC pipes to work in the arms. I created a PVC pipe bearing. You can easily make your own with two pieces of pipe that fit together well. You will want to cut a small piece of the 1.25 inch PVC to protect the costume. After that, cut the 1 inch PVC pipe so that it can rotate in the 1.25 inch pipe. You need to be careful with this because if you just used plain pvc pipe you could wear away the joint very easily. Even if you use plaster of paris to reinforce the joint it will still crack away over time and it won’t last very long.

Since the cosplay allows for a lot of space I was able to make the body huge and cavernous. As such, I was able to keep my arms inside the costume and didn’t have to have them coming out of it. Since that was the case, I put in puppet arms to make the costume look more in character. It was pretty easy to do. All you need is a pipe with decorative bits with foam decorative bits and some PVC bearings. I decided that heat shaping the PVC pipe for the arms was the best because it was cheaper and was easier to do since you wouldn’t need to install a bunch of joints. For this type of bend you want to heat it evenly and completely over the entire outside surface of the pipe. You want to get it right the first time. If you have to do it multiple times you make the bend in the PVC weaker every time. Heat up the PVC and then press the inner edge in to how much you want it bent. Then you will need to wait for it to cool. The outer edge will solidify and be a bit stronger than the inside edge. If you don’t do it right, the inside will start to crack, especially if you keep on bending it in and out.

If you look at the videos, I would actually cover the feet now. However, I have chosen to finish the arms first in the blog post. In order to start with the fist, I cut the basic shape out of foam then glued the layers together like how we did the main body part. I drew the idea of what I wanted the fist to look like onto the surface of the foam with marker. Since you’re carving out something out of a block you need to envision what’s inside and slowly work your way in. The best way is to start with the most exposed parts of the glove and then keep on working in. I found that it was the best to find was the thumb and the knuckle before I started to work in other details after that very slowly, sanding and shaping the foam to get the hand that I wanted.

In order to support all the foam that was glued together to make the hand I used huge foot long shish kabab skewers to laterally link all the foam together. That way, if the glue isn’t gluing properly together, all the skewers are going to be holding it together. It provides additional support and ensures that everything will stay together. I put a shish kebab skewer every three inches. One of the hands required a curve and for that one I inserted even more skewers to make sure the prop stayed together. The hands didn’t need crossbracing. Just inserting the skewers were enough.

In order to put the fist on, you will need to create a hole to jam over the pipe. If you jam just the foam on over the pipe you will be dependent on just friction to hold the foam over the pipe. I took plaster of paris and threw it into the hole that was in the foam before I sprayed insulation 78 on the pipe and jammed it all together to make sure that it stuck and held well.

I also had to make the small elbow pieces out of foam. I screwed a PVC disk onto the elbow and then glued the foam to the PVC Disk (PVC will take screws but foam will not).  As such, I used the small PVC disk as a transfer to hold the foam in place.

Now I progressed to the feet. One of my hard rules is to make sure you wear comfortable shoes! You’ll be walking a lot in these cosplays and it does your body no good to be walking in uncomfortable shoes for long periods of time. Also, for these shoes, I needed to do some foam parts. These big foam parts are prone to snapping off if you don’t reinforce them.

To start these I made a shoe print out of wood. After that, I took a pair of my comfortable shoes and screwed the shoe into the wood at the toe and the heel. Note that if you use wood, it can be really hard to walk around on concrete, tile, or other hard surfaces since the wood is so smooth. To give the shoes some friction, I chose to layer the very bottom of the wooden shoe portion in cardboard since it is easily replaceable, cheap, and would provide some kind of friction. You can also use foamies or other soft and pliable materials for the shoe. Having friction really helps you to get around, especially if you’re walking in clunky shoes.

Note, foam doesn’t glue well to wood. To make it stronger on the foot I put wonderflex around the bottom edge of the shoe (since wonderflex sticks to most stuff). You will want to stick the wonderflex on before the plaster of paris. Wonderflex sticks better to porus surfaces and it sticks onto wood because of the grain. If you have a nicely waxed wood it won’t stick as well.

After you put on the wondrflex and the foam, you will want to use a lot of plaster of paris to cover of the shoe and to fill in the holes of the foam before you start sanding. Now you can get rid of the layer rings. You can plaster of paris the entire surface before sand down the rings that you can see so that you will be able to hide the pieces. When you’re using plaster of paris you need to store it well when you are not using it. I like keeping it in a water container. If the brush hits the air it hardens and then you need a new brush. I use my hand, brush, and a spackle tool. There are a number of ways to get it on. After you finish sanding it, you’ll want to coat it to make it stronger.

Next I progressed to the horns that jolt out from the side of the head. They are very easily broken and are very important to the costume. I had to do a lot of crossbracing in these horns to make sure that they didn’t go anywhere since they were so easily broken. The glue wasn’t going to hold well to the horns either, given how pointed and narrow they were. I used approximately 5 skewers in each horn to ensure that they weren’t going to break and worked primarily with foam because it is good at giving textures and gives a different feel to the final product.

In order to shape the foam for the horns, I opted to use a hot knives. AS A NOTE, HOT KNIVES ARE VERY DANGEROUS. BE VERY CAREFUL. A handy tool to have around for foam is a pumpkin carving tool. There are saws called foam saws and they come to a really sharp point. They allow you to puncture through the foam without killing a huge surface area. Pumpkin carving knives are smaller than foam saws and do the same thing. They are great for precision cuts and are pretty cheap, especially after Halloween.
We ran into an issue with transporting it so we cut it in half. However, cutting it straight in half would be bad for holding it together so I cut it in a zig zag pattern so there would be more surface area. In addition, I could add a skewer to the cosplay straight through the zigzags to hold it in place at the con.  

With this all being done, it was time to paint the piece. Since I only did it a few days before the convention there was no time to nitpick on details. I opted for this cosplay because it is steampunk based and the genre allows you to kind of mess around with how smooth and polished it looks. Steampunk is basically just metal all around so I chose to use a metallic paint. In order to paint with a metallic paint you will need a base. The fists were green so I started with a green base before I painted with a metallic green. I used around three bottles of brown paint to cover the main part of the cosplay before I started to work on the gold metallic color. I wanted to have a non-uniform tone so I used three different kinds of gold and copper metallic and worked them in layer by layer. While this sounds like a lot of work it really isn’t. You’ll mainly be plopping it on and mixing it with your hand to get the creases in. After you complete the metallic coating you will want to get the colors you want for oil and strategically degrade the paint job. If you have cracks in places that you want to emphasize, get a wash and cover that section in it so that it will bring out the imperfections. The flaw is built into the character of the costume.

Note, when you are painting the PVC Pipe be sure to sand it before you paint or the paint will come right of.
I also did some bits of decorative wonderflex work before I painted. You would typically put wonderflex on before plaster of paris but since it is decorative the detail has to be undamaged so it needs to go after the plaster of paris. Since it is only decorative it isn’t holding any weight so it doesn’t matter if it isn’t as strongly structured.

I totally didn’t treat this costume well at all. It needs to be repaired. For the damaged wonderflex,  I I have to do is just heat it back up and put it back on. Since it is a steampunk costume, all I did was just took dirty colors and made it part of the character. There is some thought you need to put into mud and oil. If you blotch it on it can look ok but if you put it on like how it might have happened in real life (like how oil might leak from a crack) it looks more realistic. I had layers that I sheared apart just enough to damage the paint job. To hide that you need to take a heavier paint and work it in there or else it will just look like rings.

That’s the Golem cosplay tutorial! As always, please feel free to email us at finalcosplaycorps@yahoo.com if you have any questions or check out our Youtube at  http://www.youtube.com/user/FinalCosplayCorps

Tuesday, December 20, 2011

Let's Make Cosplay: Lightweight Horns for Head




In this tutorial I will cover how to make a set of lightweight horns for your head. When making horns for your head you want to make sure they are light. If you make heavy horns for your head it will drag on your head and put pressure on your neck and spine. They can also fall off and move around, which is less than ideal. Making them lighter will make it easier to mount, and for horns like these you will want them mounted fairly well. 

I chose to use the following materials: EPS foam, shish-kabob skewers, plaster of paris, gesso, wonderflex, yellow and papaya acrylic paint, head band, cement glue, and varnish.
  
I used the following tools: hand saw, wasp, paint brush, sponge brush, 60 and 180 sanding sponge, and yanky push drill. 

To begin with, I opted to use a headband to stabilize the horns. They would provide the best method of securing and stabilizing the long horns to your head. DO NOT use spirit gum or prosthetic adhesive. Those kind of materials are dangerous to use with horns that are as big as the ones we are making in this tutorial because they can damage your skin when they fall off and they won’t last that long. It’s best and easier to use a headband. Many artists chose to use prosthetic glue to fasten the horns onto their heads because they see actors use it for their props. However, actors don’t wear horns for extended periods of time and prosthetic glue is not a good idea if you want to use it to keep your horns on all day long during a convention. The easiest way to do this is to put a headband underneath the wig and attach the horns to the headband through the wig.

To start the prop I decided to begin with foam. Take your saw and you can begin to cut the basic shape out of the foam with the saw. After you cut the basic shape you can use the rasp to give it a basic round form. Since foam needs to be smoothed out I chose to use a rough sanding sponge (60) to smooth out the foam and to get the large pink pieces out of the horns.

Once you’re done shaping and smoothing your horns out of the foam you will want to reinforce the horns internally so that they have more rigidity and stability. I took skewers and pushed them into the horns so they would be more stable. I also used the skewers to mount the horns to the headband by drilling holes into the headband and then gluing them into place. After that, you will need to take some wonderflex and use it to cover over the foam. This will act as a coating over the foam because you will need to cover the horns with some plaster of paris. The plaster of paris will peel off the foam so the wonderflex will act as a base for the plaster of paris to stick to. Apply the wonderflex to the skewer portion in the headband as well.

However, as you put the wonderflex around the side of the horns you need to be careful so they don’t show around the side of the horns. In order to make sure the wonderflex doesn’t mold in an odd way around the edge of the horns I chose to stop the wonderflex about an inch or so above the end of the horn. This way, the edge would not fold funny and it would be hidden with the wig.

Now it’s time to coat the horns in plaster of paris. I chose to start with a plaster of paris mix mixed with water because this creates a smoother application. I also expected that the horns wouldn’t be worn for long lengths of time, given that the horns were much bigger than the six inch rule that most conventions have in place. After the plaster of paris fully dried, I took a sanding sponge and sanded down the plaster of paris to go with the brush strokes that I would use when I painted the horns. Then, I opted to use a traditional brush instead of a sponge brush to give the horns stream marks from the tip to the base so that they looked like horns.

Now, I’ve noticed that most people choose to paint the horns in yellow, orange, and red. However, these aren’t the correct colors. The colors tends to be a medium color between yellow and orange, which tends to be a difficult color to paint since you need a really dense pigment paint to paint yellow. Artist paints are usually the best pigmented paint but it is usually  extremely expensive. You’ll need to put in multiple layers. I opted to coat three thin layers of yellow on the entire horn as a base coat. Once I was happy with the color I mixed a papaya orange (which is a red orange ish color) with yellow to get the medium color I was looking for. In order to get a straight, crisp line, get some painters tape and wrap it around the section that you want to protect from paint. Start on top of the painter’s tape and brush away from it to get a nice line. I did two more layers of the mixed color paint over the initial coat and then did the same thing with the straight papaya paint on the last section of the horns.

These horns ended up light and durable enough that the headband wasn’t needed. The person I made these for ended up reshaping the wonderflex at the base of the horns into a bunch of tabs before he punched some holes into it so that he could sew the horns into the wefts of the wig. He painted the tabs and the bottom of the horns black before he varnished it with three layers of glossy varnish.
That’s our tutorial on these fun horns! If you have any questions, please feel free to check us out on Facebook or email us at finalcosplaycorps@yahoo.com!

Wednesday, November 30, 2011

Let's Make Cosplay: Mini Post: Specialty Edges for Blades

This is a mini blog post where I wanted to talk about how you could create a specialty edge on a blade. This is an extension off of the sheathed sword blog post and in this post I’ll walk you through how to do a wavy edge on a blade with aluminum tape.

This is tricky because you need a light tape so that it doesn’t rip the aluminum tape. Painter’s tape sticks too much and would be too hard to remove. Tape like masking tape, which doesn’t have as much adhesive, would be ideal.

What you should do is attach this tape to the blade’s edge and then draw out whatever wavy edge design that you want to have on the blade. Use an exacto knife and run it along the wavy lines you drew carefully so that you can pull off a piece to expose the first edge. Sand that one way. After you sand it, put the tape back over that section and peel off the tape from the other section. Sand that in a direction different to how you sanded the first section and you’ve got a specialty edge! 

Let's Make Cosplay: Sheathed Sword



The sheathed sword prop was a prop that was a Youtube watcher suggested. It was a really interesting prop that I wanted to make so I chose to create it and gift it to the viewer, especially because I wanted to create a set of videos that also covered how to make a sheath that would comfortably hold a sword properly without denting the tip of the blade (which is a common problem with many sheathes). Most sheathes have a flat bottom and causes the tip of the blade to wedge flat onto the bottom which damages the tip. Interested in seeing how this prop was made? Check out our videos at http://www.youtube.com/user/FinalCosplayCorps/search?query=sheathed+sword

The materials I used were as follows: lambent flooring, 1/8 inch medium density fiber board (MDF), #4 half inch Philips flat head wood screws, 1/2 inch PCV pipe, 1/2 inch wood dowel rod, aluminum tape, a wood ring, friendly plastic, poster board, white glue, cement glue, red pleather, and acrylic paint (tan,gold and mango colors).

The tools that I used were as follows: a hand saw, an exacto knife, a heat gun, a yanky push drill, a Philips screwdriver, a rasp, a file, a pair of scissors, some sponge brushes, a 80 and 150 grit sanding sponge, a fine tip marker, and some rulers.

Before we start I want to cover some issues with aluminum coating. Before you coat anything in aluminum coating you need to make sure you start with a firm and ridged material. Aluminum coating wrinkles really easily. If you start with a flexible or flimsy material the sword will bend and the coating will wrinkle. In order to combat that the sword needs to be strong, firm, and sturdy so it doesn’t bend and the sheath also protects the sword and keeps the sword straight while it’s sheathed so it bends less and thus lasts longer.



In order to make the sheath you will want to cut it out of the same wood as the blade and at the same size so that it will fit snugly. After that, the other portions of the sheath can be made out of whatever wood you want. I made the sheath with three layers. There is a top layer, the middle layer, and the inside layer. The middle layer of the sides of the sheath are the wood that is made from the same material as the blade. I glued some poster board to give some more wiggle room on the inside of the sheath so it would help protect the blade. You need to be able to gauge the friction that will happen when pulling the sword out of the sheath or sliding it back in and the poster board helps decrease the friction.

After I get all those portions cut out (the sides and the insert at the bottom of the sheath to protect the bottom of the blade) and the poster board glued in I took a wood planer and rounded the edges of the sheath, making sure that everything lined up before I finished rounding the edges of the sword and sheath. If you find any holes in the sheath after you’re done rounding off edges and you put the sheath together you can use friendly plastic to fill them.

After you’re done with that portion of the sheath you can move to the handle of the blade. I chose to use a piece of ½ inch pvc pipe. I cut a slit down one side of it so that I could heat up the pipe and wrap it around the nub I made on the blade to insert it into the handle. You can heat up the pipe with a heat gun. After you’re done wrapping the PVC over the nub you need to put screws through the PVC and into the nub potion to keep the handle firmly onto the sword. You’ll want to do 4 to 6 screws (2-3 on each side of the handle). If your sword weighs more, you’ll want to put in more screws for support.

In order to make the ring portion of the handle I decided to take a wood ring. The problem with using wood is that you always have to be careful in regards to the grain. If you screw against the grain in the wood it will cause the wood to splinter. Since wood rings have grains that go in every direction it is impossible to put in a screw in a wooden ring because it would splinter. Since I couldn’t screw it in to mount the ring into the handle I chose to use friendly plastic because it is extremely hard and durable after it’s dried. I put a small slit in the ring so that it would mount a little better to the PVC pipe before I globbed on friendly plastic to make sure that the ring sticks extremely well and firmly to the PVC handle. Friendly plastic sticks quite well to things that are rough in texture and this helped to anchor the ring and the PVC together.

After the friendly plastic dried and fully hardened I took some red pleather and began to wrap it around the handle. I mounted the pleather to the PVC pipe with a screw before I glued around it to make sure that it stayed firmly and didn’t get pulled off. After that, you need to wrap up the handle, overlapping the pleather halfway over the piece before it so you get a thick double layer grip and a nice crease. After you wrap it fully from the top of the handle to the bottom you need to put a screw in the other end through the pleather and into the PVC. Make sure the wrapping around the PVC pipe is tight so that it doesn’t slip so that you lose your grip.

After you’ve got these parts all assembled and ready to go you can get ready to paint. You should sand all the edges of the sheath to make sure that all of them are smooth and you should also lightly sand the ring so that it will take well to the pain and not have weird textures across the wood.

Since there are holes where screws are on the sheath I used friendly plastic to hide the holes.
As a note, I choose to use friendly plastic as a patcher because I use my heat gun for a lot of crafting and the friendly plastic works well with that. It’s not an end all patcher. You could also use resin. I just prefer friendly plastic because it’s more convenient for me.

To start painting, you will need to put a base coat on the prop of whatever color you want the prop to be.  With dark gold I use a brown base coat. If it’s a light gold I use a tan or a grey depending on what color the gold is. Metallic paints don’t take to whatever you’re painting the first time so you need a base coat. The primer you choose changes up how the metallic color will show later.

After you paint and varnish the sword and sheath it’s time to bring out the aluminum tape. For this, patience is the most necessary thing you need. You have to be VERY careful because this material is VERY easy to wrinkle or to misalign. Also, if you don’t have a big piece of aluminum tape to cover an area, take advantage of existing lines and edges to hide the creases. You’ll need about one foot wide aluminum facing tape. Contact paper brushed nickel also exists so you could use that as an alternative. Note, you don’t want to layer aluminum tape over itself because you can see the edges come through and it look like cracks. Also, make sure that you use a very stable and unmoving material as a base.

While you’re attaching the aluminum tape you need to peel away the adhesive protection slowly and work with it. Take a straightedge (I used a putty tool) to push it down. As you go make sure there are no air bubbles or cracks. Get it done. At some point you might have to layer over a piece of aluminum. Try to get it to stick as little as possible over the edge. Cut the edge with the exacto knife to pull the piece of aluminum tape away and you have a clean edge from piece to piece with no overlap.

The trick to making it look realistic is to sand it. For this, you’ll need some sanding sponges. You’ll want a rougher sanding sponge for the side of the blade that needs to look like it is being used. Just use it a little bit to give some direction and nick so that it looks like it’s being sanded against a stone. Use a lighter sanding sponge for the side that isn’t being used to remove the shine.

If you want to bring out the grooves you can also go in with a wash to bring out the scratches that you put in with the #35 sanding sponge and it will create more detail work. If you do it right you’ll have enough grit to distinguish it from the sword without it looking super old.



That’s the tutorial for this weapon! I did have some tips about how you could do a custom specialty edge on your blade and we’ll have that up in another blog post following this one titled specialty blade edges. As always, if you have any questions please check out our youtube or email us at finalcosplaycorps@yahoo.com! 

Monday, November 21, 2011

Mini Post: Technique: Base Painting

Base painting is EXTREMELY important when you go to paint a prop. Coating a prop with a base coat of paint ensures that later layers will stay on the prop and that it all paints evenly. It also smooths out the surfaces and makes sure the paint will go on more evenly. It is a good idea to coat with a base color similar to the color the prop will be. However, altering the color of the base coat will alter the color of the top coat overall.

Do note: you ALWAYS need to make a base coat for metallic paints. :)

Mini Post: Technique: Dry Brushing

Dry brushing is a nice way to put on some detail onto a prop. They can give an allusion of lines or shadows. The key to dry brushing is that you take as much paint off the brush as possible. Brush specific areas and then go into deeper areas to pound the pigment in. You should stay with blacks or dark browns when dry brushing to get the best effect. Also, you should also make sure to do a wash prior to dry brushing. 

Let's Make Cosplay: Creepy Book



This book was made for a person who suggested it as a prop. The premise behind this book would be that it would look like it was floating. The person who wanted the book suggested that we use acrylic but that really didn’t work because it would be too heavy if it was made purely out of acrylic. He also wanted to make sure that it bounced and looked like it was moving while it was floating.  You can find all the videos corresponding with this prop on Youtube at http://www.youtube.com/user/FinalCosplayCorps/search?query=Creepy+Book .

The list of materials I used are as follows: 1 inch eps foam, 1/4 inch eps foam, 1/4th inch MDF, twist ties, poster board, 1 carbon fiber rod, 1/8 inch pvc sheeting, heavy bundling wire, strapping, wonderflex, paint (you will need tan, black, brown, gold, and silver), fishing line, varnish IPS weld on 2007, cement glue, #4 half in, Philip flat head wood screws #8, 1.5 inches Philips flat head wood screws, and finishing nails. 

            The tools that I used were as follows: hand saw, exacto knife, heat gun, sculpting tools, yanky push drill, Philips screwdriver, hole puncher, dropper, syringe dropper, dremmel, box cutter, rasp, file, scissors, sponge brushes, colored fine tip markers, rulers, and circle template.

The fist thing you're going to need to make is the support structure. This structure is going to be your base. Without it there is really no way the prop will be able to sit up properly and be supported. The support structure will have two parts; the book and a harness structure that will be the base to hold up the book.

           For the book, the easiest way to have done this would be to make it out of foam. However, foam is not extremely strong and it is easily damaged. You could easily have gaping holes where you can see the inside foam. We will start with the foam and later add PVC to cover over it to protect it.

           
            The harness will push a plate onto his back with two brass tubes. The brass tubes would be where the carbon fiber rods would slide in and as such would fit snugly, giving the allusion that the book was floating. If the tube wasn’t in the right position you could bend the tubes to be in the right position or you can bend the tubes to bring them up up or down to shift the friction and make it easier or harder to take off.

                In order to make the book bounce I chose to install carbon fiber rods to make the book wiggle a bit and allow it to bounce. When completed, the book will look like a book with two rods sticking out of the bottom. In the original design, the carbon fiber rods were supposed to go through a jacket and get into the tubes.

First, you will need to heat up the carbon fiber rod and bend them before you tie them down to the foam. To attach the support plate to the foam I drilled holes in so that there was a place to use twist ties to hold the carbon fiber rods together to the support plate. The plate is in the center of the book to take all the weight so that everything can be mounted to the support plate instead of the foam. After that, I took two pieces of foam and cut them to the size he wanted and then cut a piece of 1/4 inch foam sheeting and made a hole in it so that it would fit so that it looked like two pieces of foam with another piece sticking out. This was all glued together with insulation 78.

Obviously foam is not the most durable material so the cover of the book is going to be made with PVC sheeting. It’s also thermafomable so you can do the entire book binding in one piece with the PVC sheeting. I took a big rectangle and shaped a binding by folding over the edges twice.

Next, if you look at reference pictures, there were metal bits on the inside of the binding. To recreate that in the prop I took some wire and bent u shape staples. I painted them in black then gold before I mounted them into the PVC and then mounted the PVC to the foam since it would be hard to paint after it was mounted. After that, I painted the inside cavity so that that section would be done. I would normally paint everything last but since this was an interior piece and there were other details going on top of this stuff it was necessary to paint it first.

In order to give the book more protection I cut some pieces of mdf wood to cover the book and make sure that it was protected. The book was only around half a pound but it was still kind of heavy for what it was made to do.




With the back and binding done it’s time to work on the face. I positioned the face and then realized that I had to cut off a chunk of the front cover so that I could inset the layers that were going to come on after it. I heated up the PVC sheeting, cut it out, put a depression in the foam to accommodate the face and details of the book. Unfortunately, this required me to reposition some screws that were mounting the front cover, back cover, and foam to the central support plate. After I adjusted the screws and made sure that everything would be covered up and they provided the necessary support I took another bit of PVC sheeting and heated it up before I pushed it into the hole.

I then began to work on the decorative cover, making sure that I had it all glued together with ip 2007 plastic glue. Making sure that it is screwed and glued ensures you that it definitely mounted. Make sure that everything you want done is done correctly before this step because you won’t be able to pull the prop apart after this.

After that, I sanded up the binding so that I could give it a correct texture. I used a rasp to give it the scratchy look and after that I began to work on stencils for the details that were going to go on the book. This is where you basically try your best to recreate a specific pattern or detail that you want.

After this, I created a decorative edge for the back with wonderflex. In order to attach the wonderflex you will need to heat it up with a heat gun before you put it on the back. This will cleverly hide all the screws as well.

After I’m done stenciling and putting on that edge I put on the piece of one inch foam and draw the face onto the foam as much as I can. After you draw on the face, you can use your rasp and start cutting into the most defined areas. Leave areas that are supposed to stick out alone. After you do that, you might go back in and redraw the face again so that you can plan how you’ll carve the rest of it. After you’re done carving the face you will need to get some more wonderflex and heat it up before you stretch it all across the foam face. Press the wonderflex firmly against the foam so that you can get all the details. Using sculpting tools to do this will help define your lines better. The wonderflex is strong and durable and ensures that you won’t have foam pieces breaking off of the book. After you’re done with the wonderflex, you can put your stencil up to the top of the book and make sure everything’s stenciled right. Do NOT use sharpie or marker because that will bleed easily. Use paint or a base coat so that it won’t show through the paint. Put everything in where you want it to go and make sure everything looks in place.

Once everything is in place, mark everything on the wonderflex before you slowly take out the warm wonderflex off of the foam. Then you can slowly carve all the details out of the wonderflex and paint it. Make sure you cover the prop with a base coat. Start off with a flat color, especially because we will need to dry brush later to give the book an older appearance. After you paint the book with a base color you can wash the entire thing (paint washing the entire prop allows for the foam to take on some more texture). I used grey as the base coat for the silver paint. Don’t forget, you HAVE to base coat anything before painting with metallic paint because metallic paint tends not to stick. I also washed the inside of the book because there are lots of cracks and crevices in the book and I wanted to pull out all those details. The only part that you should not wash is the portion with the gold detailing because the gold detail looks so new and shiny.

Once you have the binding on the book you should take a saw and run slits down the foam to make it look like the book has pages. You will need a really fine blade to do this job because if you use a thick blade it will not look realistic. After that, you can take a rough sanding sponge and run it down the lines so that it looks more like pages and thus mitigates possible damage.

Now it’s time to dry brush. The key to dry brushing is that you take as much paint off the brush as possible. Brush specific areas and then go into deeper areas to pound the pigment in. You should stay with blacks or dark browns when dry brushing and it is best to dry brush after putting the wash on the prop.

After this, I painted the silver pigment on the face and put a black wash onto it to bring out the details on the face. If you didn’t wash the face it would be much harder to see the detail when you take a picture of the prop. After that, I painted the back with a un-uniform metallic silver. To do this, you need to put blotches on the paint and then work into the paint that is already on the surface.

In order to define one of the edges of the book I took a dry brush and began brushing a lighter color on at an 90 degree angle to make it look like it had more of an edge on the side that was being used the most. I used a tan bit on the binding on the side and for the pages because you are trying to  bring out different which brings out the emphasis on how pages look. You want to do this same technique with raised edges as well. However, make sure you are not using metallic paint with this technique because you cannot see the detail.

After you are done painting you will just need to put everything together.

I chose to finish this prop a different way because the person who wanted this prop wanted the prop to extend much farther than what we agreed upon. I chose to finish this with a stand which involved me taking long strips of acrylic. I heated them up and bent them (one piece for a central stand and two for smaller legs to make an X). You can glue these together with IPS #3 for acrylics and then set some screws in there to ensure that all three pieces are stuck together. Unfortunately, with the new method I went about this I had to open up the book again so that I could adjust how I was going to mount this. I opened the book up and cut out the carbon fiber rods and I used the screws that were holding the book to the center plate to stop the acrylic sheeting when it was inserted into the book. I cut a notch into the foam so that there was a slit for the plastic acrylic to slide into the book and hit the screws. The foam allows the book to be held in place on the acrylic sheeting.

Do note, a piece of acrylic is not really strong enough to hold weight, especially in wind. It will flop over. I heated up the main shaft and curved it so that it would have more strength and be able to hold more and be more resistant to breaking. Bending the plastic gives it more area to apply force as compared to a straight piece that is easier to snap. I also attached another piece of plastic on the base of the main piece of acrylic that is going straight up to add additional support. The pieces of clear acrylic sheeting look like a pyramid. Do your best to keep it blemish free because if you scratch it the effect will be damaged. If you don’t look for it you cannot see the acrylic stand. However, since the prop is extremely top heavy a good wind will knock it over. Be VERY careful when you’re moving around. I suggest that if you’re walking that you should take it off and put it on only when you’re getting a picture taken.





That’s it for this prop! As always, if you have any questions please feel free to email us at finalcosplaycorps@yahoo.com! 

Sunday, November 6, 2011

Let's Make Cosplay: Prop Sword


This was an interesting prop that I had made for one of my assistant’s friends.

I used the following materials: 5 inch pcv pipe, 3 millimeter silver acrylic sheeting, IPS Weld on #3, friendly plastic, resin, a carbon fiber rod, EPS foam, plastic skulls, 3M insulation 78, plaster of Paris, white glue, hot glue, #4 half in, 4 inch Philips flat head wood screws, one inch philips flat head wood screws, and black and sliver acrylic paint.

I used the following tools: a hand saw, a hot knife, a heat gun, a yanky push drill, a Philips screwdriver, a rasp, a file, sponge brushes, an 80 grit sanding sponge, a mixing container, some mixing sticks, paper towels, a fine tip marker, and some rulers.

To start off this prop, I began with cutting the silver acrylic. Now, most people probably won’t be using this because it is extremely expensive and rare to find. However, I chose to use this material because of its look. I began by drawing my template onto the plastic. Your sword will differ depending on what sword you’re looking to create and the reference art you have.

In order to create a crisp ridge along the spine of the sword you’ll need to use the hot knife to cut in the middle of the sword before you bend it. The line that you cut into the back of the blade will make a sharper edge. After you make this incision you will need to start heating up the acrylic before you can start to shape the sword before you put these two pieces together to form the sword.

After you have finished molding both sides of the sword pieces you will need to put both pieces together. You should start by taping these pieces in place so that the pieces line up correctly and that they match each other. Slowly use the heat gun to heat up both pieces of the acrylic pvc sheeting while gluing them together with the ips weld on #3 for acyrlics. Be careful with the heat or you may cause the plastic to deform. This process is also very difficult because you need to make sure you seal the entire sword up completely or the resin will leak out.

Note: If you find that you have holes when you pour in your resin you can use some friendly plastic to seal those holes temporarily until the resin hardens. I checked to see if it leaked by testing it with water and plugged all the holes with friendly plastic before I went any farther.

Before you pour the resin in you want to insert something into the blade that reinforces the structure a little more. I used a carbon fiber rod and a long piece of PVC pipe down the length of the sword. This would be reinforced by the resin and allow for more stability and rigidity through the entire prop. After that, I filled the entire sword with resin and allowed it to harden and dry.

While that’s sitting you can focus on the more complicated parts of this prop.  I definitely found this to be the ribcage and the arms. I cut EPS  foam for all these pieces and used insulation 78 spray to glue them all together. Insulation 78 spray is really easy to use. All you do is spray the pieces that are going to be stuck together, rub the pieces together to make sure that the entire surface is covered, let it sit for a bit so that all sides can get slightly sticky, and then put those pieces all together. After all the pieces are stuck together you can begin to use the rasp and files to cut the basic shape out.

Some people ask about you can manipulate the texture of foam. The texture of your foam differs with how well you sand the foam. Sanding foam is much easier to sand than other materials. For this prop, a more pitted look was more ideal so I left it that way. I made some plaster of Paris to paint onto the foam and fill in details. After the plaster of Paris is dry you can work to sand the plaster of Paris to work on whatever form you want to make.

Now we want to attach the entire piece together. This is EXTREMELY IMPORTANT because you need to make sure the entire prop is well supported throughout the entire piece. If there isn’t good structure there will be no way to do any action with the prop without it breaking so make sure that your prop is structured well throughout. The blade is well structure with the PVC rod, carbon fiber rod, and resin. You will need to make sure the handle and the base are well supported as well.

I chose to attach the chest piece onto the sword before putting anything else onto the blade. I attached this piece with hot glue.  

After that, I used the hot knife to cut through the plastic of the blade where the sword arms would be inserted and stuck in before I cut out the section that the handle would be inserted in.

In order to get the skull details on the sword, I used the plaster of Paris to fill the skulls to give them more rigidity and strength. The horns that went onto the sword were made from pieces of PVC sheeting cut into triangles. Lightly heat them with a glue gun before you wrap them into cones.

After these details were done, I used the hot glue gun to mount the arms in place and to attach the skull onto the sword. In order to make sure the skull stayed on the prop I inserted a screw into each skull which also held open the jaw for a more eerie and creepy look. You will need to put filler into the sides of the skulls to make them look nice. White glue and plaster of Paris will get the job done.

After that all that is done it is time to paint the skull section of the prop. I used acrylic paint mixed with plaster of Paris to paint the skulls. The reason I mixed the paint with the plaster of Paris was to ensure that in case the skulls got damaged the paint job wouldn’t matter too much because it would be painted all the way through.

After this it’s time to finish some more minor details for the prop. I made the decorative bits for the handle and the tip of the cone out of foam. It’s much easier to sculpt and shape the detailed bits from foam. After you cut those pieces and finish them you can glue and mount the decorative bits for the handle. Then you can move to cut the grip for the handle from the foam. You can use the same trick for the sword to do the grooves of the handle, cutting in the middle before you cut out the curves. These curves go on the outside and is purely decorative. After that, you cut the triangles out for the spikes.

After all the foam pieces are cut cover all of it in modpodge. This is to give it elastic resistance to cracking. By covering it in modgpodge the prop will take damage and the paint will stretch. I personally used three layers of modpodge on these pieces to make sure that they were fully covered.

After that I primed all the foam and everything else that hadn’t been painted to be painted, using a black paint to cover everything. Don’t forget, priming pieces with paint before you do your paint job is very important! After the black primer coat was dry I began painting the silver. I used a dry brush to brush on the silver paint and dabbed at the prop with the brush so that the prop looked like it was made out of bone and that the dented parts looked more dented.

That is the basic gist of how I made this prop sword! If you’re interested in more details, please check out all the related videos on our youtube, located at http://www.youtube.com/user/FinalCosplayCorps . If you search prop sword you will find our individual videos for that project! As always, if you have any questions, feel free to shoot us an email at finalcosplaycorps@yahoo.com or find us on facebook at https://www.facebook.com/pages/Final-Cosplay-Corps/201702463225417

Wednesday, September 14, 2011

Let's make Cosplay: Batty Hammer



Hello! This blog post for Let’s Make Cosplay is dedicated to the Batty Hammer! I accidentally broke one of my girlfriend’s props and so this was what I made for her to make up for that. If you want to see more detailed videos about how to make this fun prop, check out Knives' videos on Youtube at http://www.youtube.com/user/FinalCosplayCorps/search?query=Batty+hammer

First things first. Here is the list of materials and tools you will need.

                Materials: You will need: approximately five feet of 0.5 inch pcv pipe, around 3 feet 0.5 inch dowel rod, 3/4 inch PVC pipe, one inch PCV pipe, wonderflex, resin, a 4 inch cardboard tube, EPS foam, 3M insulation 78, #8 one inch Philips flat head wood screws, washers, black and sliver acrylic paint, and varnish.

Tools: You will need a hand saw, an exacto knife, a heat gun, a dremmel tool, a yanky push drill, a Philips screwdriver, a rasp, a file, some sponge brushes, a paint brush, a 80 grit sanding sponge, a mixing container, some mixing sticks, some paper towels, a fine tip marker and rulers.

The first thing we have to do is layer the PVC pipe for the handle. In order to do this you will need to heat them up with the heat gun to make them expand. After you do that you’ll need to fit them all up into each other. The half inch PVC is for the handle. You will put the 3/4th inch PVC pipe over that and 1 inch over that. You will be putting the hammer head on the top of this pipe and adding the stuff on the bottom of this setup.

In order to avoid sculpting all of the parts I decided to choose to layer pieces of pipe over other pieces to achieve the same effect. However, since the pipes are different thicknesses I chose to do other details with wonderflex.

I chose to utilize a half inch dowel rod to give the handle more rigidity. I inserted the wood into the bottom so that it could give some support and act as a plug for the bottom so that I could pour resin into the entire handle portion and around all the different size tubes. If you would like to learn more about mixing resin please consult the blog post for that. I have realized that it’s much better to fill the entire base with wood, so next time I may choose to do this method with more wooden dowel rods.

Now we need to move to the hammer head. I wanted to create a dented metal look so I chose to make the endcaps out of foam. Since foam has a frazzled and weird texture it can be painted to look like dented metal. It also makes the end caps nice and soft so if the weapon is actually used it won’t hurt on impact, thus making it safer for photoshoots.

You will need to start by cutting slits at the top of the handle. After you cut these slits you are going to heat them up and bend them so that you can turn them into tabs that can hold screws that will go into the hammerhead. After that you will need to begin sculpting, shaping, and carving the designs with a handsaw. After the detailwork is done you should get the wonderflex (which is good for detail work). Heating up the wonderflex allows it to be applied to other surfaces (you can heat it with water but I prefer to heat it with my heatgun). I completed the bottom of this prop with wonderflex scraps. Never throw away wonderflex scraps! You never know when you’ll need them!  

After you’re done with the head of the hammer, heat up the top of the pipe and start attaching the head of the hammer to the handle. Make sure you put in heavy screws. Note, this is a bad support structure for a prop like this but this is a very small hammer so no big deal.

Next we’ll work on the wings for the hammer. Again, using wonderflex for this is great. I chose to cut the frames out before I cut and stretched the wonderflex and formed the wings over scrap to do the raised part in the wings (similar to sculpting it out of clay). Just make sure you keep it in its shape until it’s cool or the shape will fall out! I chose to make the crosses out of wonderflex as well since it mounts well to itself once it’s heated up.

Now to get started with painting. Make sure you PRIME everything before you paint it. If you don’t, the paint job will be inconsistent. Plastics ESPECIALLY do not take paint well so you have to prime the materials with a base coat first.

Once you’re ready to mount everything else together after priming the prop, grab a washer and set it on top of the crosses and wings before you screw it all together onto the hammer. The washer protects the wonderflex from the screw so that it won’t rip through the material.

After that, start working with the silver paint. Metallic paints are weaker for pigment so you’ll need to base coat over the primer with a similar color. I chose to spray paint the head of the hammer. HOWEVER, note that spraypaint eats through foam. If you choose to spraypaint the hammer make sure the areas with foam are well covered. Tape off areas that you aren’t painting a specific color and go back to those sections after the paint dries and you can take off the tape safely.

In order to give the prop a more defined look I chose to base it in silver paint before I did a black wash. The black will go into all the cracks and crevices and shows the details of the hammer much more clearly.  After that I did some dry brushing to illustrate some more wear marks and dents. The dry brushing leaves some ray edges as highlights where it’d be more shiny in war and it also allows other parts to have more shadows.





There you have it! A batty hammer! As always, if you have questions, please feel free to contact us at finalcosplaycorps@yahoo.com and check out our videos on our Youtube channel!