Let's Make Cosplay: Creepy Book

This book was made for a person who suggested it as a prop. The premise behind this book would be that it would look like it was floating. The person who wanted the book suggested that we use acrylic but that really didn’t work because it would be too heavy if it was made purely out of acrylic. He also wanted to make sure that it bounced and looked like it was moving while it was floating.  You can find all the videos corresponding with this prop on Youtube at http://www.youtube.com/user/FinalCosplayCorps/search?query=Creepy+Book .

The list of materials I used are as follows: 1 inch eps foam, 1/4 inch eps foam, 1/4th inch MDF, twist ties, poster board, 1 carbon fiber rod, 1/8 inch pvc sheeting, heavy bundling wire, strapping, wonderflex, paint (you will need tan, black, brown, gold, and silver), fishing line, varnish IPS weld on 2007, cement glue, #4 half in, Philip flat head wood screws #8, 1.5 inches Philips flat head wood screws, and finishing nails. 

            The tools that I used were as follows: hand saw, exacto knife, heat gun, sculpting tools, yanky push drill, Philips screwdriver, hole puncher, dropper, syringe dropper, dremmel, box cutter, rasp, file, scissors, sponge brushes, colored fine tip markers, rulers, and circle template.

The fist thing you're going to need to make is the support structure. This structure is going to be your base. Without it there is really no way the prop will be able to sit up properly and be supported. The support structure will have two parts; the book and a harness structure that will be the base to hold up the book.

           For the book, the easiest way to have done this would be to make it out of foam. However, foam is not extremely strong and it is easily damaged. You could easily have gaping holes where you can see the inside foam. We will start with the foam and later add PVC to cover over it to protect it.

           

            The harness will push a plate onto his back with two brass tubes. The brass tubes would be where the carbon fiber rods would slide in and as such would fit snugly, giving the allusion that the book was floating. If the tube wasn’t in the right position you could bend the tubes to be in the right position or you can bend the tubes to bring them up up or down to shift the friction and make it easier or harder to take off.

                In order to make the book bounce I chose to install carbon fiber rods to make the book wiggle a bit and allow it to bounce. When completed, the book will look like a book with two rods sticking out of the bottom. In the original design, the carbon fiber rods were supposed to go through a jacket and get into the tubes.

First, you will need to heat up the carbon fiber rod and bend them before you tie them down to the foam. To attach the support plate to the foam I drilled holes in so that there was a place to use twist ties to hold the carbon fiber rods together to the support plate. The plate is in the center of the book to take all the weight so that everything can be mounted to the support plate instead of the foam. After that, I took two pieces of foam and cut them to the size he wanted and then cut a piece of 1/4 inch foam sheeting and made a hole in it so that it would fit so that it looked like two pieces of foam with another piece sticking out. This was all glued together with insulation 78.

Obviously foam is not the most durable material so the cover of the book is going to be made with PVC sheeting. It’s also thermafomable so you can do the entire book binding in one piece with the PVC sheeting. I took a big rectangle and shaped a binding by folding over the edges twice.

Next, if you look at reference pictures, there were metal bits on the inside of the binding. To recreate that in the prop I took some wire and bent u shape staples. I painted them in black then gold before I mounted them into the PVC and then mounted the PVC to the foam since it would be hard to paint after it was mounted. After that, I painted the inside cavity so that that section would be done. I would normally paint everything last but since this was an interior piece and there were other details going on top of this stuff it was necessary to paint it first.

In order to give the book more protection I cut some pieces of mdf wood to cover the book and make sure that it was protected. The book was only around half a pound but it was still kind of heavy for what it was made to do.

With the back and binding done it’s time to work on the face. I positioned the face and then realized that I had to cut off a chunk of the front cover so that I could inset the layers that were going to come on after it. I heated up the PVC sheeting, cut it out, put a depression in the foam to accommodate the face and details of the book. Unfortunately, this required me to reposition some screws that were mounting the front cover, back cover, and foam to the central support plate. After I adjusted the screws and made sure that everything would be covered up and they provided the necessary support I took another bit of PVC sheeting and heated it up before I pushed it into the hole.

I then began to work on the decorative cover, making sure that I had it all glued together with ip 2007 plastic glue. Making sure that it is screwed and glued ensures you that it definitely mounted. Make sure that everything you want done is done correctly before this step because you won’t be able to pull the prop apart after this.

After that, I sanded up the binding so that I could give it a correct texture. I used a rasp to give it the scratchy look and after that I began to work on stencils for the details that were going to go on the book. This is where you basically try your best to recreate a specific pattern or detail that you want.

After this, I created a decorative edge for the back with wonderflex. In order to attach the wonderflex you will need to heat it up with a heat gun before you put it on the back. This will cleverly hide all the screws as well.

After I’m done stenciling and putting on that edge I put on the piece of one inch foam and draw the face onto the foam as much as I can. After you draw on the face, you can use your rasp and start cutting into the most defined areas. Leave areas that are supposed to stick out alone. After you do that, you might go back in and redraw the face again so that you can plan how you’ll carve the rest of it. After you’re done carving the face you will need to get some more wonderflex and heat it up before you stretch it all across the foam face. Press the wonderflex firmly against the foam so that you can get all the details. Using sculpting tools to do this will help define your lines better. The wonderflex is strong and durable and ensures that you won’t have foam pieces breaking off of the book. After you’re done with the wonderflex, you can put your stencil up to the top of the book and make sure everything’s stenciled right. Do NOT use sharpie or marker because that will bleed easily. Use paint or a base coat so that it won’t show through the paint. Put everything in where you want it to go and make sure everything looks in place.

Once everything is in place, mark everything on the wonderflex before you slowly take out the warm wonderflex off of the foam. Then you can slowly carve all the details out of the wonderflex and paint it. Make sure you cover the prop with a base coat. Start off with a flat color, especially because we will need to dry brush later to give the book an older appearance. After you paint the book with a base color you can wash the entire thing (paint washing the entire prop allows for the foam to take on some more texture). I used grey as the base coat for the silver paint. Don’t forget, you HAVE to base coat anything before painting with metallic paint because metallic paint tends not to stick. I also washed the inside of the book because there are lots of cracks and crevices in the book and I wanted to pull out all those details. The only part that you should not wash is the portion with the gold detailing because the gold detail looks so new and shiny.

Once you have the binding on the book you should take a saw and run slits down the foam to make it look like the book has pages. You will need a really fine blade to do this job because if you use a thick blade it will not look realistic. After that, you can take a rough sanding sponge and run it down the lines so that it looks more like pages and thus mitigates possible damage.

Now it’s time to dry brush. The key to dry brushing is that you take as much paint off the brush as possible. Brush specific areas and then go into deeper areas to pound the pigment in. You should stay with blacks or dark browns when dry brushing and it is best to dry brush after putting the wash on the prop.

After this, I painted the silver pigment on the face and put a black wash onto it to bring out the details on the face. If you didn’t wash the face it would be much harder to see the detail when you take a picture of the prop. After that, I painted the back with a un-uniform metallic silver. To do this, you need to put blotches on the paint and then work into the paint that is already on the surface.

In order to define one of the edges of the book I took a dry brush and began brushing a lighter color on at an 90 degree angle to make it look like it had more of an edge on the side that was being used the most. I used a tan bit on the binding on the side and for the pages because you are trying to  bring out different which brings out the emphasis on how pages look. You want to do this same technique with raised edges as well. However, make sure you are not using metallic paint with this technique because you cannot see the detail.

After you are done painting you will just need to put everything together.

I chose to finish this prop a different way because the person who wanted this prop wanted the prop to extend much farther than what we agreed upon. I chose to finish this with a stand which involved me taking long strips of acrylic. I heated them up and bent them (one piece for a central stand and two for smaller legs to make an X). You can glue these together with IPS #3 for acrylics and then set some screws in there to ensure that all three pieces are stuck together. Unfortunately, with the new method I went about this I had to open up the book again so that I could adjust how I was going to mount this. I opened the book up and cut out the carbon fiber rods and I used the screws that were holding the book to the center plate to stop the acrylic sheeting when it was inserted into the book. I cut a notch into the foam so that there was a slit for the plastic acrylic to slide into the book and hit the screws. The foam allows the book to be held in place on the acrylic sheeting.

Do note, a piece of acrylic is not really strong enough to hold weight, especially in wind. It will flop over. I heated up the main shaft and curved it so that it would have more strength and be able to hold more and be more resistant to breaking. Bending the plastic gives it more area to apply force as compared to a straight piece that is easier to snap. I also attached another piece of plastic on the base of the main piece of acrylic that is going straight up to add additional support. The pieces of clear acrylic sheeting look like a pyramid. Do your best to keep it blemish free because if you scratch it the effect will be damaged. If you don’t look for it you cannot see the acrylic stand. However, since the prop is extremely top heavy a good wind will knock it over. Be VERY careful when you’re moving around. I suggest that if you’re walking that you should take it off and put it on only when you’re getting a picture taken.

That’s it for this prop! As always, if you have any questions please feel free to email us at finalcosplaycorps@yahoo.com! 

Let's Make Cosplay: Prop Sword

This was an interesting prop that I had made for one of my assistant’s friends.

I used the following materials: 5 inch pcv pipe, 3 millimeter silver acrylic sheeting, IPS Weld on #3, friendly plastic, resin, a carbon fiber rod, EPS foam, plastic skulls, 3M insulation 78, plaster of Paris, white glue, hot glue, #4 half in, 4 inch Philips flat head wood screws, one inch philips flat head wood screws, and black and sliver acrylic paint.

I used the following tools: a hand saw, a hot knife, a heat gun, a yanky push drill, a Philips screwdriver, a rasp, a file, sponge brushes, an 80 grit sanding sponge, a mixing container, some mixing sticks, paper towels, a fine tip marker, and some rulers.

To start off this prop, I began with cutting the silver acrylic. Now, most people probably won’t be using this because it is extremely expensive and rare to find. However, I chose to use this material because of its look. I began by drawing my template onto the plastic. Your sword will differ depending on what sword you’re looking to create and the reference art you have.

In order to create a crisp ridge along the spine of the sword you’ll need to use the hot knife to cut in the middle of the sword before you bend it. The line that you cut into the back of the blade will make a sharper edge. After you make this incision you will need to start heating up the acrylic before you can start to shape the sword before you put these two pieces together to form the sword.

After you have finished molding both sides of the sword pieces you will need to put both pieces together. You should start by taping these pieces in place so that the pieces line up correctly and that they match each other. Slowly use the heat gun to heat up both pieces of the acrylic pvc sheeting while gluing them together with the ips weld on #3 for acyrlics. Be careful with the heat or you may cause the plastic to deform. This process is also very difficult because you need to make sure you seal the entire sword up completely or the resin will leak out.

Note: If you find that you have holes when you pour in your resin you can use some friendly plastic to seal those holes temporarily until the resin hardens. I checked to see if it leaked by testing it with water and plugged all the holes with friendly plastic before I went any farther.

Before you pour the resin in you want to insert something into the blade that reinforces the structure a little more. I used a carbon fiber rod and a long piece of PVC pipe down the length of the sword. This would be reinforced by the resin and allow for more stability and rigidity through the entire prop. After that, I filled the entire sword with resin and allowed it to harden and dry.

While that’s sitting you can focus on the more complicated parts of this prop.  I definitely found this to be the ribcage and the arms. I cut EPS  foam for all these pieces and used insulation 78 spray to glue them all together. Insulation 78 spray is really easy to use. All you do is spray the pieces that are going to be stuck together, rub the pieces together to make sure that the entire surface is covered, let it sit for a bit so that all sides can get slightly sticky, and then put those pieces all together. After all the pieces are stuck together you can begin to use the rasp and files to cut the basic shape out.

Some people ask about you can manipulate the texture of foam. The texture of your foam differs with how well you sand the foam. Sanding foam is much easier to sand than other materials. For this prop, a more pitted look was more ideal so I left it that way. I made some plaster of Paris to paint onto the foam and fill in details. After the plaster of Paris is dry you can work to sand the plaster of Paris to work on whatever form you want to make.

Now we want to attach the entire piece together. This is EXTREMELY IMPORTANT because you need to make sure the entire prop is well supported throughout the entire piece. If there isn’t good structure there will be no way to do any action with the prop without it breaking so make sure that your prop is structured well throughout. The blade is well structure with the PVC rod, carbon fiber rod, and resin. You will need to make sure the handle and the base are well supported as well.

I chose to attach the chest piece onto the sword before putting anything else onto the blade. I attached this piece with hot glue.  

After that, I used the hot knife to cut through the plastic of the blade where the sword arms would be inserted and stuck in before I cut out the section that the handle would be inserted in.

In order to get the skull details on the sword, I used the plaster of Paris to fill the skulls to give them more rigidity and strength. The horns that went onto the sword were made from pieces of PVC sheeting cut into triangles. Lightly heat them with a glue gun before you wrap them into cones.

After these details were done, I used the hot glue gun to mount the arms in place and to attach the skull onto the sword. In order to make sure the skull stayed on the prop I inserted a screw into each skull which also held open the jaw for a more eerie and creepy look. You will need to put filler into the sides of the skulls to make them look nice. White glue and plaster of Paris will get the job done.

After that all that is done it is time to paint the skull section of the prop. I used acrylic paint mixed with plaster of Paris to paint the skulls. The reason I mixed the paint with the plaster of Paris was to ensure that in case the skulls got damaged the paint job wouldn’t matter too much because it would be painted all the way through.

After this it’s time to finish some more minor details for the prop. I made the decorative bits for the handle and the tip of the cone out of foam. It’s much easier to sculpt and shape the detailed bits from foam. After you cut those pieces and finish them you can glue and mount the decorative bits for the handle. Then you can move to cut the grip for the handle from the foam. You can use the same trick for the sword to do the grooves of the handle, cutting in the middle before you cut out the curves. These curves go on the outside and is purely decorative. After that, you cut the triangles out for the spikes.

After all the foam pieces are cut cover all of it in modpodge. This is to give it elastic resistance to cracking. By covering it in modgpodge the prop will take damage and the paint will stretch. I personally used three layers of modpodge on these pieces to make sure that they were fully covered.

After that I primed all the foam and everything else that hadn’t been painted to be painted, using a black paint to cover everything. Don’t forget, priming pieces with paint before you do your paint job is very important! After the black primer coat was dry I began painting the silver. I used a dry brush to brush on the silver paint and dabbed at the prop with the brush so that the prop looked like it was made out of bone and that the dented parts looked more dented.

That is the basic gist of how I made this prop sword! If you’re interested in more details, please check out all the related videos on our youtube, located at http://www.youtube.com/user/FinalCosplayCorps . If you search prop sword you will find our individual videos for that project! As always, if you have any questions, feel free to shoot us an email at finalcosplaycorps@yahoo.com or find us on facebook at https://www.facebook.com/pages/Final-Cosplay-Corps/201702463225417

Let's make Cosplay: Batty Hammer

Hello! This blog post for Let’s Make Cosplay is dedicated to the Batty Hammer! I accidentally broke one of my girlfriend’s props and so this was what I made for her to make up for that. If you want to see more detailed videos about how to make this fun prop, check out Knives' videos on Youtube at http://www.youtube.com/user/FinalCosplayCorps/search?query=Batty+hammer

First things first. Here is the list of materials and tools you will need.

                Materials: You will need: approximately five feet of 0.5 inch pcv pipe, around 3 feet 0.5 inch dowel rod, 3/4 inch PVC pipe, one inch PCV pipe, wonderflex, resin, a 4 inch cardboard tube, EPS foam, 3M insulation 78, #8 one inch Philips flat head wood screws, washers, black and sliver acrylic paint, and varnish.

Tools: You will need a hand saw, an exacto knife, a heat gun, a dremmel tool, a yanky push drill, a Philips screwdriver, a rasp, a file, some sponge brushes, a paint brush, a 80 grit sanding sponge, a mixing container, some mixing sticks, some paper towels, a fine tip marker and rulers.

The first thing we have to do is layer the PVC pipe for the handle. In order to do this you will need to heat them up with the heat gun to make them expand. After you do that you’ll need to fit them all up into each other. The half inch PVC is for the handle. You will put the 3/4^th inch PVC pipe over that and 1 inch over that. You will be putting the hammer head on the top of this pipe and adding the stuff on the bottom of this setup.

In order to avoid sculpting all of the parts I decided to choose to layer pieces of pipe over other pieces to achieve the same effect. However, since the pipes are different thicknesses I chose to do other details with wonderflex.

I chose to utilize a half inch dowel rod to give the handle more rigidity. I inserted the wood into the bottom so that it could give some support and act as a plug for the bottom so that I could pour resin into the entire handle portion and around all the different size tubes. If you would like to learn more about mixing resin please consult the blog post for that. I have realized that it’s much better to fill the entire base with wood, so next time I may choose to do this method with more wooden dowel rods.

Now we need to move to the hammer head. I wanted to create a dented metal look so I chose to make the endcaps out of foam. Since foam has a frazzled and weird texture it can be painted to look like dented metal. It also makes the end caps nice and soft so if the weapon is actually used it won’t hurt on impact, thus making it safer for photoshoots.

You will need to start by cutting slits at the top of the handle. After you cut these slits you are going to heat them up and bend them so that you can turn them into tabs that can hold screws that will go into the hammerhead. After that you will need to begin sculpting, shaping, and carving the designs with a handsaw. After the detailwork is done you should get the wonderflex (which is good for detail work). Heating up the wonderflex allows it to be applied to other surfaces (you can heat it with water but I prefer to heat it with my heatgun). I completed the bottom of this prop with wonderflex scraps. Never throw away wonderflex scraps! You never know when you’ll need them!  

After you’re done with the head of the hammer, heat up the top of the pipe and start attaching the head of the hammer to the handle. Make sure you put in heavy screws. Note, this is a bad support structure for a prop like this but this is a very small hammer so no big deal.

Next we’ll work on the wings for the hammer. Again, using wonderflex for this is great. I chose to cut the frames out before I cut and stretched the wonderflex and formed the wings over scrap to do the raised part in the wings (similar to sculpting it out of clay). Just make sure you keep it in its shape until it’s cool or the shape will fall out! I chose to make the crosses out of wonderflex as well since it mounts well to itself once it’s heated up.

Now to get started with painting. Make sure you PRIME everything before you paint it. If you don’t, the paint job will be inconsistent. Plastics ESPECIALLY do not take paint well so you have to prime the materials with a base coat first.

Once you’re ready to mount everything else together after priming the prop, grab a washer and set it on top of the crosses and wings before you screw it all together onto the hammer. The washer protects the wonderflex from the screw so that it won’t rip through the material.

After that, start working with the silver paint. Metallic paints are weaker for pigment so you’ll need to base coat over the primer with a similar color. I chose to spray paint the head of the hammer. HOWEVER, note that spraypaint eats through foam. If you choose to spraypaint the hammer make sure the areas with foam are well covered. Tape off areas that you aren’t painting a specific color and go back to those sections after the paint dries and you can take off the tape safely.

In order to give the prop a more defined look I chose to base it in silver paint before I did a black wash. The black will go into all the cracks and crevices and shows the details of the hammer much more clearly.  After that I did some dry brushing to illustrate some more wear marks and dents. The dry brushing leaves some ray edges as highlights where it’d be more shiny in war and it also allows other parts to have more shadows.

There you have it! A batty hammer! As always, if you have questions, please feel free to contact us at finalcosplaycorps@yahoo.com and check out our videos on our Youtube channel! 

Lets Make Cosplay: Mecha Chibi Wings

Hey guys! This is the blog post containing the instructions for Mecha Chibi Wings! A viewer asked for this tutorial but she’s a teeny tiny Asian girl so big mech wings won’t work for her. Chibi wings are much more reasonable for a girl her size to carry and wear around as part of a cosplay. If you're interested in looking at the videos which have more details about how to make this fabulous prop, please check out the videos on Youtube at http://www.youtube.com/user/FinalCosplayCorps/search?query=mecha+chibi+wings

The first thing you want to do before you start building any project is to make a preliminary plan or schematic. I recommend you try to make a plan or schematic for a few reasons.


1.       You can use a schematic to estimate the cost of the project by planning out what materials you are going to use, how much of it you will need to buy, and any equipment you may need. It allows for you to start a rough budget what you’re going to do, which is always good when your checkbook is feeling a pinch! I always price my things on the back of the schematic to see how much my project will roughly cost me. As a side note to budget management, the key is to not do a lot of big projects frequently. I have a huge mech project like once a year or a big project that’s like $600. That’s bad as a huge chunk but not as bad if I break it down into small payments over the course of the year.
2.      Creating a schematic also allows you to plan out how you’re going to create the prop so that you’ve got a guide on how you’re going to do it and you aren’t fumbling around as you make the prop. This way you can try to foresee some problems that might occur and adjust for them ahead of time so you don’t waste materials (and money) later on.
3.       A schematic also gives you an estimated weight and look of the final project.

Alright, so before we get started you’ll need your tools and materials. For this project we needed the following materials. You need 3mm. PVC sheeting in red, white, and black colors. You will also need 3mm. transparent red acrylic sheeting, IPS Weld on #3, a 2 mm. carbon fiber rod, two push release key rings, some medium density fiber board (MDF), #4 half in, some Philips flat head wood screws, marine power PC 11, and some black and red acrylic paint. The tools you will need include a hand saw, heat gun, yanky push drill, Philips screwdriver, pliers, rasp, file, sponge brushes, 80 grit sanding sponge, fine tip marker, and rulers.

The first thing that we want to make is a back support.

Having a back support piece is crucial because it allows the weight of the prop to spread across your entire back so you aren’t putting the entire strain on your shoulders. If you watched the video you can see what kind of shape I cut out and how I molded  it to my body so that the weight isn’t all on my shoulders. This kind of back support spreads the weight evenly across my entire back and it is heat formed to fit my body so it’s nice and comfortable.  Having this kind of a back support is so much nicer than having to put all the weight just on my hips, shoulders, or my back.

With that being said, the first thing that were going to do for our chibi wings is make the back support. Since we are making heavy ones and not your typical feather wings, you will need a plate to steady the wings so they don’t flop everywhere. You will also want something to harness the wings to (like a bra).

We’ll start off with a piece of PVC. The reason we choose to use pvc is because it is thermaformable. For her, I want this to be 8 inches by 4 inches. I cut out two separate plates. One of the plates is going to attach to the bra later on and another one of the pieces will attach to the wings themselves as the main support.

If you look at the first video you will see what kind of shape I chose to cut out.  You will need two of these pieces cut out. The reason for this second piece is so that it will support the wings on your back to make sure that they don’t flop over.

After you’ve figured out how big you need it cut to fit yourself you can cut on the plastic. If you’ve never cut plastic before I have posted a tutorial online for that and you can check it out (NEED LINK). As you cut, be aware of the angles that you are cutting. Some of these angles may be very small and it will be harder to cut from that side. Cut from the side with the widest part that needs to be cut and move to the smaller angle.

Now that you have both your parts cut out, we need to punch some holes in so that we can create supports on the side so that these wings will stay even and not sag in one direction. In order to do this we’re going to drill some small holes. The more holes that you put in means the more support this piece will get since the weight will be distributed over a large area. I’ve decided to put nine holes on each side.

Now guys, this is super important. When you drill these holes make sure that these holes are ¼ inch apart. If you put them more apart then you put extra pressure on the thread you will handstitch in later. If you put the holes closer together the thread can saw its way through the plastic over time.

So now you’ve got two plates cut to fit you with the holes punched in. Time for your next step. Pick one of the two pieces as the one you want to strap to the bra. This will be what pushes against your body and supports the rest of the piece. Now make sure that you file down all the corners. The last thing you want is for some sharp and pointy corner to be digging into your back.

After you file all the corners and make sure they’re rounded off you’ll want to get the heat gun. We’re going to use that gun to shape the support so that it molds to your back. You’re going to want to roll the edges up a little bit so that they don’t push into your skin. This piece will be under whatever costume she’s wearing. The other piece will be on the wings itself and doesn’t pose as big a problem. This piece that we’re working on now ensures that she can put the wings on or take them off without taking off her shirt. Mark this piece with an X so you make sure that you don’t confuse the two pieces.

So we need to have these lock together. The piece that you want to be directly on your skin on your back will be worn underneath your shirt and the piece that connects to the wings directly will be on the outside.  We need to have these lock together quickly and easily. For this she will need to put a buttonhole on the back of her shirt or have a shirt that buttons up in the back. The bra will support  the wings. Hopefully we will make these wings as light as possible and we won’t put too many elements into this.

So here we’ve got two small rings and two small clasps. These are going to be used to lock our wings to the support. We want two of them to make sure that the wings don’t pivot. What we need to do is insert the clasp into one piece and we want to insert the two rings into the other piece.

So how do we get these rings onto the PVC? Well, we are going to start out by drilling a hole smaller than the ring itself. We will need to make a hole in the middle. You will need to make sure that the tool you are using will drill a hole smaller than the ring. Carefully push a hole into the middle of both pieces of the back support.

After you’ve pushed your hole in, pick up your heat gun and heat the PVC. Be careful to make sure that the plastic doesn’t bent its shape. We want it soft enough that it will be easy to fit the ring in. Go ahead and poke the ring into the hole. The ring has small lips and we want to make sure the PVC wraps around those edges.

Now we’re going to put the clasp into the other piece. This one we want to mark because we have to make sure the clasp and the ring line up are even. If they don’t line up the prop will be unbalanced and structurally weaker. After you mark your hole, drill into it again. Keep in mind that these fittings need to be really snug. If they aren’t the props won’t hold properly and they won’t be as structurally sound. This side we have to make sure we know what side we’re putting the clasp in. The other one didn’t matter as much because the ring is the same on both sides. Since the clasp has buttons on one side that lock onto the lip of the rings we need to make sure that we insert the clasp so that the buttons will match on the right side to push the panel with the support.

As a note, all of you can likely see that there’s a small gap between the two panels. That is to allow for her shirt to sit in between the two panels. Don’t worry about that. The wings will stay stable as long as we put two rings and clips.

Now it’s time to start the actual wing parts. I chose to go with matte colored PVC because it is easier to work with. Acrylic is nicer and more pricy but I use different tools for that so to keep it simple for this prop I chose to go with the matte.

Draw your wing frame shape out first. After you draw this out you can begin sawing out the pieces from the PVC. MAKE SURE that you keep things small when using acrylic vinyl. PVC sheeting is fragile so try to keep them small to reduce the risk of damage. I chose to use MDF for the base of the wing frame. Since this is just the frame it doesn’t need to be thermoformed or altered. It just needs to be cut. This material is stronger and cheaper so it’s good to use.

As you see at 4:40 in the 3^rd video of the series, located at http://www.youtube.com/user/FinalCosplayCorps#p/search/10/Bpr5V0srvlM you can see that I chose to use more of an L shape. This will be how the wings stick out from the back. I will have two pieces of this cut with one piece of acrylic in the middle and I will put as many screws through these pieces in the middle as I can so that it will hold in place without breaking.

Since you need one for each side you will need to cut a total of four L pieces of the first PVC and two L pieces with the acrylic. This way you have two pieces of regular PVC and one piece of acrylic for each side. After you cut all your pieces we will need to put the screws in.

To make sure that the wings can have a little bit of spring we will have to make sure that we don’t mount them directly to the center piece. To do this we will mount them using an acrylic rod. The rod I chose to use was a 2 millimeter rod. It’s thin but it’s still really strong. I’d suggest using carbon fiber rod. It’s pretty expensive so I’d recommend just getting what you need (any specific amount). DO NOTE: One problem that you will have is combining the materials. I don’t have the really strong cement stuff that you’re supposed to use but for now I’m going to put it into the center piece.

In order to get this rod in I need to drill a hole big enough to thread the rod through. You will want to put this hole about two inches in from the end of the wing frame. After you drill the hole you will heat up the carbon fiber rod and set it between both frames before you bend it so that both ends are parallel with the frames and they stabilize the wings to the support. After you attach the wings that way we need to make supports to make sure that the wings won’t snap off. I chose to make a triangular section out of MDF right underneath each wing so that it would help prop the wings up.

After you’ve got the base done you’ll need to pull out your colored PVC. Cut your pieces to how you want them to look for each wing. We will be screwing the PVC into the support before we use the heat gun to thermaform the plastic. Notice that we’ll be layering all the PVC strategically so that each upper layer covers over the screws underneath it.

When you heat this plastic you need to make sure the gun is always moving and that the light is just on one part you get hot and cold zones . You can warp the plastic or burn it if you don’t do this correctly. Also, you need to be very careful when dealing with acrylic PVC. It’s super fragile but can be thermoformed. However, it melts at a much lower temperature so be careful when you use it.

The girl who suggested this prop ended up getting thick bindings to use. She picked up bindings similar to the ones that are used on backpacks and that is how she added additional support in addition to the back support.

There we go! Chibi Mecha Wings! If you have any questions please feel free to ask! 

Who and What is the Final Cosplay Corps?

Final Cosplay Corps (FCC) is a group of extremely dedicated and passionate group of cosplayers who avidly attend anime conventions around the country. The group is made up of a great bunch of people who love to create impressive works of cosplay. However, the members of FCC are just as dedicated in trying to help other cosplayers reach their highest potential as well. Everyone involved with FCC started from the bottom and worked to achieve the workmanship they have now. Contrary to many elitist cosplayers, the cosplayers in FCC take pride in helping other fellow cosplayers learn how to improve their skills. They understand that everyone needs to start somewhere and love to help others grow and learn more.

FCC started unofficially after Chris Farabaugh (Millions_Knives) went to his first anime convention and decided to work on large cosplays after that. Since these cosplays often required the help of multiple handlers, Chris and his friends often worked together to make sure that he could get around conventions without risking other people’s safety. The group officially formed at Anime Central in 2008 and was finally titled Final Cosplay Corps at the C3 Picnic in 2008.

Knives often looks for people with a variety of skill sets to join the group. Also, he respects all cosplayers that do their craft well, even if their craft utilizes materials he personally prefers not to use. He is trying to gather people with various developed skills to join FCC so that the group can help each other and others.

Currently FCC is broken up into three divisions, Core Members, Ninjas, and the Tactical Squad.

The core members are the members who specialize in cosplay construction.
Chris Farabaugh: millions_knives: Specialization in Prop Constuction
Seneca Farmer: This_chick 25: Specialization in Sewing
Amanda Saleski: haku_hei: Specialization in 2-D Design
Eric Kubicek: spazchan: Specialization in Steampunk
Bret Luitze: Akiba64: Specialization in Cardboard Prop Construction

Ninjas are members who choose not to cosplay or help with construction but help the group with other things.
Blake Williams: djeclectic: Ninja of Automobiles and Music
Trent Wexler: rawkz0rz: Ninja of Visual Effects and Media
Kim Jarvis: gadgets: Ninja of Tranportation
Jon Norman: xenoblade: Ninja of Heavy Lifting
Savannah Watkins: sweet_sunshine: Ninja of being a Chibi (Real Designation TBD)

Members of the Tactical Squad handle matters online, whether it be video promotion, blog posts, and all that fun jazz.
Sirin Avci: Fullmetal_C: To Be Announced
Nicholas Pollitt: Kasin: To be Announced
Kasey Zhong: Kasemei: Tactical Supervisor of the Facebook and Blog Posts

Have any questions for us? Please feel free to contact us via the Youtube page or here! 

Welcome to the Final Cosplay Corps Blog!

Why hello there! 

You have reached the blog site for the Final Cosplay Corps! It is likely that you have come here to look up more information about us and what we do and we would like to take a moment to thank you for visiting! We love giving out advice for cosplay help and we always love having visitors! 

If you haven't already checked out our Youtube channel please feel free to go and look at some of the great tutorial videos that Chris Farabaugh (millions_knives) has already put up there! The url is http://www.youtube.com/user/FinalCosplayCorps . We are currently working on getting blog posts up for each project and once we get all the backlog up we'll consistently keep posting up new blogs with information from the videos! 

If you have any questions for us at all, please feel free to post here, contact us on Facebook (Final Cosplay Corps), contact us on Youtube, or email us at finalcosplaycorps@yahoo.com!